The Tool Desk
Outbyte Driver Updater FREEScan for outdated or missing drivers - takes under a minuteDriver Scan →Outbyte PC Repair FREEClear out junk files and repair common Windows errorsFree Scan →Special offer. See more information about Outbyte and uninstall instructions. Please review EULA and Privacy policy.
To measure how many watts your gaming PC draws from the outlet, connect a suitably rated plug-in electricity meter between the wall socket and the PC, then read it while your chosen workload is running. For electricity used over a gaming session, track cumulative kilowatt-hours (kWh) over a known period. This measures the tower’s whole-system AC input—not just the CPU or graphics card.
Measure the PC at the outlet
- Check the meter’s compatibility and rating. Confirm that its plug and voltage suit your local electrical system, and that its maximum load is appropriate for the equipment. Follow the rating printed on the meter and its manual. The P3 P4400 manual warns, “Do not exceed maximum ratings as detailed on label.” P3 International’s P4400 manual gives model-specific instructions; its ratings should not be assumed to apply to every meter or region.
- Connect the meter directly to the wall outlet. Plug the PC into the meter, following the meter’s instructions. The P4400 manual lists a computer as an example of a device to measure.
- Decide what you are measuring. For PC-only consumption, connect the tower alone. To measure the full gaming setup, include the monitor and any other devices you want counted, and label the result accordingly.
- Take readings under defined conditions. Note the watts at idle, then while running a representative game or repeatable workload. Record the game, settings, duration, and whether the number is a momentary reading or an average. A single reading describes that particular moment and workload, not every gaming session.
- Measure energy for a whole session. Record the meter’s cumulative kWh before and after a session, along with elapsed time. The difference is the energy used during that period.
Understand watts, VA, and kWh
- Watts (W) indicate active power at the time of the reading. Use watts to compare the PC’s draw at idle and under load.
- Volt-amps (VA) indicate apparent power. Some meters display both VA and watts; use the watts figure when you mean active power, rather than treating the two readings as interchangeable.
- Kilowatt-hours (kWh) are accumulated energy over time, the quantity used for estimating electricity consumption on a bill.
Calculate average power and session cost
For a variable gaming session, average power can be more informative than a single live reading. Divide the kWh used by the session length in hours, then multiply by 1,000:
Average watts = kWh used ÷ hours × 1,000
For example, if the meter registers 0.6 kWh over two hours, the session averaged 300 W at the meter. This is an arithmetic illustration, not a typical gaming-PC result. To estimate the session’s electricity cost, multiply the measured kWh by the applicable cost per kWh on your electricity bill. JCE Co-op’s meter guide explains the energy and cost calculation; its stated 15-amp limit applies to the described meter context, not all plug-in meters.
What a wall meter tells you—and what it does not
A plug-in meter measures the combined AC power entering everything connected through it. With only the tower connected, that is a whole-computer wall-side measurement. It is not an individual CPU or GPU reading, and it includes the effect of the system’s power supply and other components as they draw power.
DriversOutdated Drivers Are Slowing You DownPerformanceWindows Errors? Fix Them Before They SpreadDriversCrashes, No Sound, or Screen Glitches?
Special offer. See more information about Outbyte and uninstall instructions. Please review EULA and Privacy policy.
#1 Best Overall
Watt Meter Power Meter Plug Home Electricity Usage Monitor 7 Modes Display
- Various Monitoring Parameters: The power meter plug can monitor the power (W), energy (kWh), volts, amps, hertz, power factor, cost, minimum and maximum power (W), cumulative days and time of your appliances. By switching 7 display modes, you can easily know the various parameters while the appliance is working. The home energy monitor can also calculate and display how much power your appliance uses and how much electricity bill it cost in cumulative time
- Upgraded LCD Display: With large screen size 2.36 inch x 1.85 inch, clearer monitor backlit, our electrical usage monitor can display the data clearer and more visible no matter day or night. 180°full wide viewing angles is great for reading and recording the data in any angles. No need to stand on the front of the display and bend over to read the numbers
- Adjustable Backlight Time: Our upgraded watt meter has 5 options of backlight time. The default backlight time duration is 10 minutes(bL-0). If you want to change the backlight time, you can press and hold "UP" and "DOWN" button at the same time to enter backlight time setting, then press "UP" and "DOWN" to select the backlight time (bL-0 =10 minutes, bL-1=1 hour, bL-2=4 hours, bL-3=8 hours, bL-4=always on), finally press the "COST" to save the backlight time settings
- Overload protection: When the power of the appliance exceeds the overload power, the LCD will display “OVERLOAD” to warn the user. All the buttons will quit working and can only be workable when you lower or remove the load power. The default overload power is 3680W and is adjustable from 0 to 3680W. In general, you need to set the overload power to 1800W before using. Just press the "function" button for more than 3 seconds to enter the setting
- Data Memory Function: The wattage meter will record your power consumption data when you remove it from socket, or remove appliances from the electricity monitor. You can directly see the last data when you use it next time. This function can also automatically save the data when there is a sudden power failure
Software readings for selected components and estimates made by adding component specifications answer different questions. They do not, by themselves, measure the PC’s actual whole-system draw at the outlet. PC Gamer’s explanation of total PC power measurement distinguishes component-based estimates from a wall-meter reading.
Choose a meter for the measurement you need
Before buying or using a meter, check that it matches your outlet and voltage, is rated for the intended load, and displays both watts and cumulative kWh if you want live power and session energy. For longer measurements, consider whether its display and logging functions will let you capture the period you care about. A P3 Kill A Watt P4400 is one example with watts and cumulative kWh displays, but suitability depends on its label ratings and your local electrical system.
Quick Recap
Bestseller No. 3
Bestseller No. 4
Best Value
Sale
HBN Watt Meter Plug with Backlight, Plug-in Socket Power Meter Electricity Usage Monitor Consumption Home Electrical Energy Monitor, Voltage Amps Wattage Electricity Usage Tester, 9 Display Modes
- ✓ Backlit LCD Display: The watt meter features an upgraded backlit LCD display with a 160° wide viewing angle, providing clear and distinct data readings from any angle, day or night. (Note: To conserve energy, the backlight will automatically turn off after 15 seconds of continuous use.)
- ✓ 9 Types of Data Display: This energy meter plug accurately monitors a wide range of electrical parameters, including power (W), apparent power (VA), energy consumption (kWh), usage time (hours), power frequency (Hz), power factor (PF), voltage (V), current (A), and electricity cost. The user-friendly interface allows you to easily read and navigate through 9 types of data with a single button.
- ✓ Save Money and Energy: By toggling through the 9 display modes, you can gain insights into various operational parameters of your devices. The home energy monitor also calculates and displays the electricity consumption and cost over time, helping you save on your electricity bills by monitoring and managing energy usage.
- ✓ Data Storage: The plug-in electricity meter stores all non-real-time data, ensuring no information is lost in the event of a sudden power outage. If data exceeds the screen’s maximum display range, the screen will flash as a reminder. Pressing and holding the reset button for 3 seconds will reset the cumulative data to zero.
- ✓ Safe to Use: Rated voltage 125VAC, 60Hz, 15A maximum 1875W resistor and tungsten wire, 1/2HP. Clean and tidy interface, very simple to use.
Rank #4
2 Pack Upgraded Watt Meter Power Meter Plug 7 Modes Display
- Various Monitoring Parameters: The power meter plug can monitor the power (W), energy (kWh), volts, amps, hertz, power factor, cost, minimum and maximum power (W), cumulative days and time of your appliances. By switching 7 display modes, you can easily know the various parameters while the appliance is working. The home energy monitor can also calculate and display how much power your appliance uses and how much electricity bill it cost in cumulative time
- Upgraded LCD display: With large screen size 2.36 inch x 1.85 inch, clearer monitor backlit, our electrical usage monitor can display the data clearer and more visible no matter day or night. 180°full wide viewing angles is great for reading and recording the data in any angles. No need to stand on the front of the display and bend over to read the numbers
- Adjustable Backlight Time: Our upgraded watt meter has 5 options of backlight time. The default backlight time duration is 10 minutes(bL-0). If you want to change the backlight time, you can press and hold "UP" and "DOWN" button at the same time to enter backlight time setting, then press "UP" and "DOWN" to select the backlight time (bL-0 =10 minutes, bL-1=1 hour, bL-2=4 hours, bL-3=8 hours, bL-4=always on), finally press the "COST" to save the backlight time settings
- Overload protection: When the power of the appliance exceeds the overload power, the LCD will display “OVERLOAD” to warn the user. All the buttons will quit working and can only be workable when you lower or remove the load power. The default overload power is 3680W and is adjustable from 0 to 3680W. In general, you need to set the overload power to 1800W before using. Just press the "function" button for more than 3 seconds to enter the setting
- Data Memory Function: The wattage meter will record your power consumption data when you remove it from socket, or remove appliances from the electricity monitor. You can directly see the last data when you use it next time. This function can also automatically save the data when there is a sudden power failure
Rank #3
Watt Meter Power Meter Plug Usage Monitor 7 Modes Display with Cord
- Various Monitoring Parameters: The power energy meter can monitor the power (W), energy (kWh), volts, amps, hertz, power factor, cost, minimum and maximum power (W), cumulative days and time of your appliances. By switching 7 display modes, you can easily know the various parameters while the appliance is working. The home energy monitor can also calculate and display how much power your appliance uses and how much electricity bill it cost in cumulative time
- Upgraded LCD Display: With large screen size 2.36 inch x 1.85 inch, clearer monitor backlit, our electrical usage monitor can display the data clearer and more visible no matter day or night. 180°full wide viewing angles is great for reading and recording the data in any angles. No need to stand on the front of the display and bend over to read the numbers
- Adjustable Backlight Time: Our upgraded watt meter has 5 options of backlight time. The default backlight time duration is 10 minutes(bL-0). If you want to change the backlight time, you can press and hold "UP" and "DOWN" button at the same time to enter backlight time setting, then press "UP" and "DOWN" to select the backlight time (bL-0 =10 minutes, bL-1=1 hour, bL-2=4 hours, bL-3=8 hours, bL-4=always on), finally press the "COST" to save the backlight time settings
- Overload Protection: When the power of the appliance exceeds the overload power, the LCD will display “OVERLOAD” to warn the user. All the buttons will quit working and can only be workable when you lower or remove the load power. The default overload power is 3680W and is adjustable from 0 to 3680W. In general, you need to set the overload power to 1800W before using. Just press the "function" button for more than 3 seconds to enter the setting
- Data Memory Function: The wattage meter will record your power consumption data when you remove it from socket, or remove appliances from the electricity monitor. You can directly see the last data when you use it next time. This function can also automatically save the data when there is a sudden power failure
Rank #2
Upgraded Watt Meter Power Meter Plug Home Energy Monitor 8 Display Modes
- Multi-function power monitor: Our electric usage monitor can monitor the power (W), electricity(kWh), voltage(V), frequency(Hz), current(A), power factor(PF), unit price($/kWh), total cost($) of your appliances. By switching 8 display modes, you can easily know the various parameters while the appliance is working. The “electricity” mode can calculate and display how much power your appliance uses. And the “total cost” mode will show how much electricity bill it cost in cumulative time
- Overload protection: When the loading power of the appliance is over the default overload threshold 1800W, the whole display with backlight and the word “OVERLOAD” will keep flashing to warn the users. Please turn off the appliance for safety concern
- Premium Material: The whole body of our energy meter is made of high-quality ABS material. It makes our home electricity usage monitor more long lasting, fireproof and anti-drop. The standard US socket and plug is suitable for all US standard appliances
- Backlight Display: With white backlight and black words, the LCD display of our home power monitor can display the data clearer and help you to read the data easier no matter day or night. The backlight will only lights up when the device is connected to AC power. If no button is pressed, the backlight turns off automatically after 10 minutes. You can also press the "UP" button to turn off the backlight manually, and press any button to turn on backlight again
- Easy to reset: No reset tool needed, our appliance power usage meter is easy to reset. You can press the “M” button for 5 seconds directly to reset the device. After reset, all cumulative data (electricity quantity, cost) will be cleared, and all settings will be restored to factory settings
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.
